Skip to content
BMX.ES
3D render of an unbranded 3-piece BMX crankset taken apart: two black chromoly arms and the steel axle with its bolts, on a skatepark ledge with steel coping and orange sunset light
Original 3D render by BMX.es (not a product photo)

Gear · 6 min read

BMX cranks: why a 1.93 m rider runs 165 mm

Why 175 mm is the standard, what changes with shorter cranks, which splines, spindle and thread to check, and four KHE options on Amazon.es.

Guide updated

See real models with verified specs ↓

Quick answer: In freestyle, 175 mm is the standard crank length, but it is not compulsory: shorter cranks (165–170 mm) bring your feet closer, give more ground clearance and make spins easier, and some Profile riders over 1.90 m run them. For a 20" BMX with a 48-spline spindle, the KHE MVP V2 set in 175 mm (812 g with axle) or the 165 mm KHE MVP arms (576 g) with their 140 mm axle; for an 18" or flatland bike, the 152 mm KHE MVP (8 splines). Before buying, match the splines, the 19 mm spindle and the 9/16″ pedal thread.

In this guide
  1. The 4 at a glance
  2. Why almost all of them are 175 mm
  3. What you gain with shorter cranks
  4. What to check before buying
  5. The 4, one by one
  6. If you are X, get Y
  7. Common mistakes
  8. Frequently asked questions

Zachery Rogers is 1.93 m tall with US size 14 shoes, and he still rides 165 mm cranks, ten millimetres under the standard. It is not a quirk: Profile Racing tells the story, in the same article where it listed cranks from 125 to 190 mm. Here is what crank length really changes on BMX cranks, what you need to match so they fit your bike, and four options available on Amazon.es on 17 November 2026.

The 4 at a glance

Three crank options and an axle from KHE available on Amazon.es on 17 November 2026

The figure is the length in millimetres: of the crank arm for the three cranks, and of the axle for the axle. All are for 19 mm spindles.

Some links are affiliate links: we may earn a small commission at no extra cost to you. As an Amazon Associate, BMX.es earns from qualifying purchases (Amazon EU Associates Programme).

Why almost all of them are 175 mm

According to Profile, racing hovered for years around 44/16 gearing with 180 mm cranks. As freestyle evolved, with lower frames and smaller sprockets, 175 mm became the unstated standard. It is what almost every 20" complete comes with.

TALL PROFILE RIDERS, SHORTER CRANKS. Height and crank length published by Profile Racing. Dashed outline: 175 mm, the freestyle standardTALL PROFILE RIDERS, SHORTER CRANKSHeight and crank length published by Profile RacingDillon Leeper1.83 m (6′0″)170 mmcame down from 175: «more responsive»Rob DiQuattro1.91 m (6′3″)170 mmshort cranks since school, for flatlandZachery Rogers1.93 m (6′4″)165 mmfeet closer: peg clearance, spinsDashed outline: 175 mm, the freestyle standard
Original BMX.es diagram. Data: Profile Racing, «Tech Tip #2: Crank it Down» (heights converted to metres).

What you gain with shorter cranks

Profile lists four advantages. First, a higher bunny hop: you jump higher with your feet closer together, just as you jump higher with your feet together than apart. Second, spins both ways (180, 360…) get easier. And the last two: less weight, because there is less steel, and more stiffness, because there is less leverage on the arm.

There is one effect you can see without tools: the pedal turns on a circle twice as wide as the crank is long. With 165 mm the pedal passes 10 mm higher at the bottom than with 175, and that is extra clearance on ledges, transitions and grinds.

PEDAL CIRCLE BY CRANK LENGTH. Diameter = 2 × crank length (drawn to scale). Pedal at the bottom, vs 175 mmPEDAL CIRCLE BY CRANK LENGTHDiameter = 2 × crank length (drawn to scale)Pedal at the bottom, vs 175 mm152 mmcircle 304 mm23 mm higher165 mmcircle 330 mm10 mm higher175 mmcircle 350 mmreference
Original BMX.es diagram. Plain geometry: the pedal turns on a circle twice as wide as the crank is long.

The downside? With less leverage, each pedal stroke pushes less. That is why racing has traditionally used long cranks. If you ride street or park, try 170 or 165. If you ride the track or like to hit the ramp fast, stay on 175. Ideally, ask to try a bike set up that way at your local park: there is the skatepark and track directory.

What to check before buying

  1. Three-piece. The cranks in this guide are 3-piece: two arms and an axle. If your bike has one-piece cranks, the swap also needs a different bottom bracket.
  2. The splines. The arms and the axle must have the same number of splines: KHE stresses it. A 48-spline arm will not go on an 8-spline axle.
  3. The spindle diameter. All four options are 19 mm, so the bottom bracket bearings must be for a 19 mm spindle. The shell type (Mid, Spanish, American) depends on the frame: we explain it in how to choose a frame.
  4. The pedal thread. 3-piece cranks take 9/16″ pedals; one-piece cranks take 1/2″. It is in the first upgrades guide.
  5. The chain side. Almost every BMX runs its drivetrain on the right (RHD). If yours is on the left (LHD), look for cranks that take both.
Splines. Spindle. Pedals. Chain side. Arms and axle must have the same count: 48 with 48, 8 with 8. 19 mm needs 19 mm bottom bracket bearings. 3-piece cranks: 9/16″ thread. RHD or LHD: the KHE MVP V2 does both. CHECK THESE 4 BEFORE YOU BUYCHECK THESE 4 BEFORE YOU BUYSplinesArms and axle musthave the samecount: 48 with 48,8 with 8Spindle19 mm needs 19 mmbottom bracketbearingsPedals3-piece cranks:9/16″ threadChain sideRHD or LHD: the KHEMVP V2 does both
Original BMX.es diagram. Data: KHE crank and axle listings, and the BMX.es parts guide.

The 4, one by one

We have not tested them hands-on: we compare what KHE and Amazon.es publish with what each rider needs. The full product cards, with pros and cons, are further down.

1. KHE MVP V2 175 mm: the standard full set

Two heat-treated 4130 chromoly arms and a 19 mm, 48-spline axle that is 140 mm long: 812 g in total, according to KHE. It takes right- and left-hand drive, comes with the sprocket and axle bolts, and fits 9/16″ pedals. Against: no bottom bracket included, and 175 mm is the long size in this guide.

2. KHE MVP 165 mm: shorter, for park and flatland

A pair of 165 mm 4130 chromoly arms, 576 g, for 19 mm, 48-spline axles and 9/16″ pedals. KHE recommends them for flatland and park. Against: arms only (with the sprocket bolts); the axle is sold separately.

3. KHE 48-spline axle: what the 165s are missing

A 19 mm, 48-spline 4130 chromoly axle, 140 mm long and 242 g, with two hollow bolts, according to KHE. It completes the 165 mm arms, or replaces yours if you have bent it. Against: it only works with 48-spline arms.

4. KHE MVP 152 mm: for 18" BMX and flatland

A pair of 152 mm 4130 chromoly arms for 19 mm, 8-spline axles, which KHE calls perfect for 18" BMX and flatland. They weigh 628 g according to KHE and 635 g on the Amazon.es listing. Against: they are 8-spline, so they do not fit the axle of the other three, and the axle is extra.

If you are X, get Y

Quick decision
If…Get
You want to swap stock cranks for chromoly without overthinking itKHE MVP V2 175 mm
You ride park or flatland and want your feet closerKHE MVP 165 mm + KHE 48-spline axle
You bent the axle of a 48-spline cranksetKHE 48-spline axle
The bike is 18" or you ride flatland on an 8-spline axleKHE MVP 152 mm
You ride the track and want maximum leverageStay on 175 mm or longer
All are for 19 mm spindles. The arm and axle splines must match.

Before you ride

Check the axle bolts after the first session. KHE says to replace the crank as soon as you see uneven wear, cracks or damage.

If I change cranks, do I need a new sprocket?

Not always. A bolt-on sprocket works if it fits the 19 mm spindle (sometimes with an adapter ring). A Spline Drive sprocket only fits spindles with its splines. It is all in the BMX sprocket guide.

Common mistakes

  • Mixing a 48-spline arm with an 8-spline axle.
  • Buying arms on their own and forgetting the axle.
  • Switching to 3-piece cranks without checking the frame’s bottom bracket.
  • Fitting 1/2″ pedals to 9/16″ cranks.
  • Picking 175 mm out of habit when you are all about spins and park.

To keep going with the drivetrain, see the sprocket, the hub: cassette or freecoaster, the pedals and all the buying guides.

Frequently asked questions

What crank length does a BMX use?

In 20" freestyle, 175 mm is the standard. Racing has traditionally used longer cranks (180 mm, according to Profile), and 18" BMX bikes usually run shorter ones, such as 152 mm.

165 or 175 mm cranks?

175 if you want maximum pedalling leverage, for example on the track. 165–170 if you ride street, park or flatland: they bring your feet closer, make bunny hops and spins easier and give more ground clearance.

Are short cranks only for short riders?

No. Profile lists riders of 1.83 m and 1.91 m on 170 mm and one of 1.93 m on 165 mm. The choice depends more on how you ride than on your height.

What does 48T or 8T mean on cranks?

It is the number of splines on the axle the arms slide onto. Arms and axle must match: 48-spline arms need a 48-spline axle.

What pedal thread do 3-piece cranks use?

Almost always 9/16″, like all four in this guide. One-piece cranks use 1/2″, and the pedals are not interchangeable.

Real models that meet these criteria

Some links are affiliate links: we may earn a small commission at no extra cost to you. As an Amazon Associate, BMX.es earns from qualifying purchases (Amazon EU Associates Programme). None of the brands in this guide sponsors it or has a commercial relationship with BMX.es: the selection is editorial and independent.

KHE

KHE MVP V2 175 mm (crankset)

3-piece chromoly crankset with a 48-spline axle

  • 175 mm · 4130 chromoly
  • 812 g with axle
  • 19 mm axle · 48 splines · 140 mm
  • 9/16″ pedals

Pros

  • Arms and axle in one box
  • Right- or left-hand drive
  • Sprocket and axle bolts included

Cons

  • Bottom bracket sold separately
  • 175 mm is the long size in this guide

KHE

KHE MVP 165 mm (crank arms)

A pair of short chromoly arms for park and flatland

  • 165 mm · 4130 chromoly
  • 576 g a pair
  • 19 mm axle · 48 splines
  • 9/16″ pedals

Pros

  • KHE recommends them for flatland and park
  • Feet closer and more ground clearance
  • Sprocket bolts included

Cons

  • Arms only: the axle is extra
  • Less pedalling leverage than 175 mm

KHE

KHE MVP 152 mm 8-spline (crank arms)

A pair of short arms for 18" BMX and flatland

  • 152 mm · 4130 chromoly
  • 628 g (KHE) · 635 g (Amazon.es)
  • 19 mm axle · 8 splines
  • 9/16″ pedals

Pros

  • KHE calls them perfect for 18" and flatland
  • Length suited to shorter legs

Cons

  • 8 splines: they do not fit a 48-spline axle
  • Axle sold separately

Keep reading

Newsletter

Join the gate.

New tracks, buying guides and riding tips. No spam.